| GENERAL |
| Cylinder Block and Crankcase Material |
Gray Iron |
| Water Jackets |
Gray Iron |
| Cylinder Heads Material |
Gray Iron |
| Valve Arrangement |
4 Valves |
| Valve Seat Inserts |
Yes |
| Head to Block Attachment |
6 Bolts / Cylinder |
| Stroke Cycle |
Four Stroke |
| Ignition Method |
Compression |
| Fuel Injection |
High Pressurized Direct Injection |
| Air Intake System |
Turbocharged, Charged Air Cooled |
| Engine Mounting |
Four Point |
| Firing Order |
1-5-3-6-2-4 |
| Crankcase Ventilation |
Breather to Atmosphere |
| CAMSHAFT |
| Number Finished |
1 |
| Bearing Material |
Steel-Backed Pb-Sn-Cu alloy |
| Number of Bearings |
5 |
| Camshaft Drive Type |
Gears |
| Material |
Steel |
| CRANKSHAFT |
| Material |
Forged |
| Heat Treatment |
Nitrided |
| Main Journal Diameters in / (cm) |
3.23 (8.20) |
| Crankpin Diameter in / (cm) |
2.87 (7.29) |
| Vibration Damper |
Viscous Rubber Damper |
| Flywheel Material |
Cast Iron |
| Main Bearing Type |
Steel Backed Pb-Sn-Cu alloy |
| Number of Bearings |
7 |
| End Thrust Taken By |
Crank Thrust Bearing |
| Total Bearing Length in / (cm) |
7.49 (19.02) |
| Total Projected Area sq. in / (sq .cm) |
24.2 (156.1) |
| CONNECTING RODS |
| Type & Material |
Forged Steel Straight Split |
| Length Center to Center in / (cm) |
7.795 (19.8) |
| Piston Pin Bushing |
Steel-backed Pb-Sn-In alloy |
| Lower End Rod Bearing Type |
Straight Split |
| Make |
Steel-backed Pb-Sn-In overlay |
| PISTONS |
| Type |
1 Piece |
| Material |
Aluminum |
| Coolant |
Oil Cooling Channel |
| Piston Pin Type |
Hollow |
| Material |
Steel |
| Diameter in / (cm) |
1.57 (3.99) |
| Retention Method |
Snap Ring |
| Piston Rings Number |
4 |
| Compression Ring Type |
Keystone |
| Compression Ring Material |
Steel |
| Oil Control Ring Type |
Bevel-Edged |
| Oil Control Ring Material |
Steel |
| VALVE OPERATING MECHANISM |
| Type |
OHC |
| Valve Guide Type |
Replaceable |
| Engine |
Carburized Steel |
| Rocker Arm Type |
Roller |
| Rocker Arm Material |
Aluminum Die Casting |
| Rocker Arm Shaft Support |
Cast Iron |
| Rocker Arm Shaft Material |
Steel |
| VALVES, INTAKE |
| Type |
Double |
| Material |
Silicon Steel |
| Number per Cylinder |
2 |
| Rotation |
None |
| Seat Angle (degrees) |
60 From Vertical |
| Head Diameter in / (cm) |
1.45 (3.68) |
| Stem Diameter in / (cm) |
0.31 (.79) |
| Lift in / (cm) |
0.46 (1.17) |
| Clearance (cold) in / (cm) |
0.016 (.041) |
| VALVES, EXHAUST |
| Type |
Double |
| Material |
Silicon Steel |
| Number per Cylinder |
2 |
| Rotation |
None |
| Seat Angle (degrees) |
60 From Vertical |
| Seat Insert Material |
Sintered Steel |
| Head Diameter in / (cm) |
1.45 (3.68) |
| Stem Diameter in / (cm) |
0.31 (.79) |
| Lift in / (cm) |
0.456 (1.16) |
| COOLING |
| Water Pump Type |
Centrifugal |
| Capacity @ Engine rpm g / (L) |
82 (310.5) per min @ 2623 rpm |
| Pump Bearing Type |
3-Ball BRG |
| LUBRICATION |
| Type Main connecting rod, camshaft bearings, rocker arms and rocker arm shaft |
Pressure |
| Camshaft lobes, connecting rod bushings, timing gear, valve lifters, piston pins and cylinder walls |
Splash |
| Oil Pump, Type |
Gear |
| Oil Pressure @ rpm psi / (kg/cm2) |
56.9 (4) @ 3100 rpm |
| Oil Intake |
Suction Bell, Rear Sump |
| Oil Seal |
Axial Type |
| Oil Cooler |
Plate Type |
| AIR INTAKE SYSTEM |
| Turbocharger |
Yes |
| Aftercooler |
Charged Air Cooled |
| FUEL SYSTEM |
| Lift Pump |
Gear Type, Integral |
| Injector Pump, Pump Model |
Denso |
| Type |
Common Rail |
| Drive |
Gear |
| Fuel Filter |
Number Used 1 |
| Type |
Fuel Flow, Paper Element |
| Location |
Left Hand Side of Engine |
| Fuel Shut-off |
Electronic |
| Turbocharger |
Yes |
| Fuel Injector Type |
Electronic Injector |
| Timing Advance |
Fixed |
